Difference between revisions of "The Machine"
(Added link to Col. Carter's rawhide.)
|Line 32:||Line 32:|
You will need to use
You will need to use rawhide. What I've found works best is goatskin rawhide, which my local Tandy Leather carries. You will need at least two pieces of rawhide for each demonstration, three or four if doing draw cuts as well.
Revision as of 15:26, 29 November 2012
By Tivar Moondragon
The Machine is based on a paper entitled Some Medicolegal Aspects of Stab Wounds by Dr. Bernard Knight, a British forensic pathologist. In his paper he describes how he tested the resistance of human skin to punctures from knives. What he found is that when the blade is set against the skin and pressed, it takes from ½ to 3 kilos (approximately 1 to 6 lbs.) of pressure to penetrate. The sharper the blade is, the easier it penetrates (which makes sense.) Dr. Knight also found that the faster the blade was moving, the easier it penetrated as well.
Don Iolo FitzOwen and Don Christian Richard Dupré of Ansteorra did some experimentation based upon these findings. They discovered that a 2-inch bend in a #5 French foil blade (the minimum kill in Ansteorra at that time) required about 4 lbs. of pressure; well within the range of Dr. Knight’s data. They also discovered that thin rawhide which had been thoroughly soaked in water gave a reasonable approximation of the penetration resistance of human skin.
The Machine is designed to allow measurement of the force required to penetrate wet rawhide with a sharp blade, in a consistent and easily demonstrated manner. The original version built by Iolo and Dupre had an embroidery hoop mounted on a postage scale. My version is designed to fold down into something that can be put in a suitcase for ease of transport.
Building the Machine
I made the base from a piece of 1 x 6 board about 16 inches (40 cm) long. The support bars that form the triangle are flat bar stock, about 1/8 x 5/8 inches (4 mm x 2 cm), and about 12 inches (30 cm) long. They are hinged at the base so they fold down for ease of storage and transport. I twisted the bar stock 90 degrees and drilled holes in the upper ends of all four pieces to hold the pivot rod. I made the pivot rod from 1/4 inch (5 mm) round bar, about 5 inches (13 cm) long.
The rawhide frame is made from more of the flat bar stock, bent into a diamond shape about 6-1/2 inches (16 cm) on a side, and bolted to the top of the center upright. The center upright is made from 1 inch (25 mm) square rod. There is a hinge attached to the bottom, which hangs down and catches the ratchet, to lock the frame so you can read the scale. See Figure 1.
Note that the distance from the center of the frame to the pivot (A to B) and from the pivot to the eye-screw (B to C) must be the same (in mine it is 8 inches (18 cm) all the other dimensions can be changed to suit your needs. You may also use whatever materials are most convenient. I built my Machine mostly from scrap material I had in my workshop.
I used a small fishing scale bought at a sporting goods store. It has a hook on the end, which hooks to the eye-screw in the back of the upright. The scale is mounted firmly on the base, so it won’t move while measuring the pressure. For the ratchet, I used a saber-saw blade, set into the base so it catches the hinge as it swings forward. See Figure 2.
You will need to use fairly thin rawhide. What I've found works best is one-ounce goatskin rawhide, which my local Tandy Leather no longer carries, but can be ordered from http://colonelcarters.com/rawhide.aspx. You will need at least two pieces of rawhide for each demonstration, three or four if doing draw cuts as well.
Using the Machine
This is how the Machine works: cut a piece of the rawhide big enough to reach around the edges of the rawhide frame. Soak the rawhide in water for at least one hour. Clamp the wet rawhide to the frame (I use four of the black metal paper clamps from an office supply store.) Mount the upright to the base by sliding the pivot bar into the holes in the support bars, and hook the scale to the eye-screw. At this point your Machine should be self-supporting. Clamp the front end of the base to the table or whatever it is resting on, with a C-clamp.
When pressure is applied to the rawhide frame, the upright will pivot and pull the scale hook forward. This is why the distance from frame to pivot and pivot to scale must be the same; otherwise the unequal leverage would give a false reading on the scale. The hinge should catch in the ratchet to allow you to read the scale, once pressure is released.
I usually start my demonstration with a fencing blade, first pressing on the rawhide with the tip until the scale reads 4 lbs. (about 2 kilos) to show the audience how little the blade must bend to reach that; then hitting the rawhide a few times with "minimum kill" blows, and reading the scale each time. (Having an assistant to read the scale and reset it for you is useful—just make sure she stays well clear of the sharp blade. See Figures 4 and 5.).
I then pick up my sharp rapier, and press it against the rawhide until it penetrates (see Figure 6). If the blade has been properly sharpened (I usually give it a final touch-up just before the class starts) the blade will penetrate at around 4 lbs. Note that once the blade has penetrated, the scale will not register any higher, because there is no more pressure on the rawhide.
I then give the rawhide a few "minimum kill" thrusts with the sharp rapier. Because the blade is moving at combat speed, it will penetrate even easier. I also demonstrate that once the blade has penetrated the rawhide, it can continue on without any further resistance. I then hit the rawhide at an angle, to demonstrate that hits that are glancing blows with a fencing blade would still penetrate with a real one.
At this point, I mount up a fresh piece of wet rawhide, and let the audience members each take a thrust at it, telling them to hit it with their usual killing blow. I will take a position where I can read the scale, and tell them how hard they hit with their thrust.
There are also two variations you can add to the presentation, if you wish. First, mount a ruler on the base of the Machine, so you can measure how deep the penetration is (bear in mind that anything more than a few inches (or half a dozen centimeters) into the torso is probably going to hit something vital).
Second, build another upright-and-pivot unit. For the rawhide frame on this one, make it square, with several curved "ribs" across the front (see Figure 8). Attach a piece of wet rawhide, and use it to demonstrate draw cuts and glancing blows. (Draw cuts will use up rawhide very quickly; make sure you have enough.) The glancing blows should penetrate the rawhide at one side, travel beneath it for a little way, and then emerge from the other side. This is a particularly graphic demonstration of how a glancing blow with a sharp blade would actually behave, especially if you add a bit of draw cut pressure as you are withdrawing the blade.